Choosing pneumatic tires and hubs for an electric skateboard gets confusing fast. Tire sizes, hub openings, hub rings, axle diameters, and bearing specs all interact, and a combination that looks right on paper can still rub your gearbox on the first ride.
This guide covers the Linnpower NEXT Quick-Release Hub system: how the 55 mm, 66 mm, and 86 mm XL hubs relate to each other, how the M and L hub rings differ, and which pneumatic tires work with each configuration.
The short answer: the three NEXT hubs are one system in three widths — 55 mm, 66 mm, and 86 mm. Width is the only thing that changes, and it decides which ring each hub takes.
The M size ring (94.5 mm tire opening) is used by the 55 mm and 66 mm hubs. The L size ring (100 mm tire opening) is used by the 66 mm and 86 mm XL hubs. The 66 mm Wide Hub is the only one that accepts both, which makes it the most flexible starting point. 6-inch tires are the exception: they need the 55 mm Standard Hub, because the 66 mm hub is too wide to seat them.
Understanding Pneumatic Tire Hub Openings
Every pneumatic esk8 tire has a hub opening: the inside diameter of the bead seat where the tire grips the hub ring. Two tires with identical outer diameters can have completely different openings, which is why tire size alone tells you nothing about hub compatibility.
Linnpower builds around two nominal opening specifications: 94.5 mm and 100 mm. Each corresponds to a specific hub ring, and the ring determines which hub you can use.
Note the three distinct measurements in the illustration. The hub opening is the inner seat. The overall diameter is the outer tire height. The tread width is across the contact patch. Compatibility is decided by the opening, but clearance on the board is decided by the other two.
How to measure your tire's hub opening
Measure the inside diameter of the tire's bead seat with calipers or a tape across the center. Do not measure the outer tire diameter, and do not measure the tread width. A reading near 94.5 mm means M size; a reading near 100 mm means L size. If your measurement falls between the two, the tire is likely not designed for either NEXT specification.
Important: matching the nominal opening is only step one. Tread width, sidewall shape, and overall dimensions also decide whether a tire seats correctly on a given hub, and whether it clears your drivetrain afterward.
One Hub System, Three Widths
All three NEXT hubs are the same quick-release system. What changes is the width of the hub center: 55 mm, 66 mm, and 86 mm. The quick-release mechanism, the axle interface, the bearing seats, and the ring design are shared across all three.
Width is the only variable, and it does two things. It decides which ring the hub takes, and it decides how wide a tread the hub can properly support underneath.
Bar length represents hub center width. Same system, three widths.
NEXT 55 mm Standard Hub
The 55 mm Standard Hub is built for smaller pneumatic tires: 6-inch tires, plus selected narrower 7-inch and 8-inch tires.
- Hub ring: M size
- Tire opening: 94.5 mm
- Axle sizes: 8 mm, 10 mm, 12 mm
- Bearings: 608 (8 mm), 6900 / 16100 (10 mm), 6001 (12 mm)
- Best suited for: 6-inch tires and selected narrower 7-inch / 8-inch tires
NEXT 66 mm Wide Hub
The 66 mm Wide Hub is the most versatile configuration in the lineup. The wider hub center supports a much broader range of pneumatic tires than the 55 mm hub.
Its main advantage is that it accepts both M and L hub rings, so one hub can run either tire opening specification.
- Hub rings: M size and L size
- Tire opening: 94.5 mm or 100 mm
- Axle sizes: 8 mm, 10 mm, 12 mm
- Bearings: 608 (8 mm), 6900 / 16100 (10 mm), 6001 (12 mm)
- Best suited for: a wide range of 160 mm, 7-inch, 8-inch, and 9-inch pneumatic tires
NEXT 86 mm XL Hub
The 86 mm XL Hub is the widest hub in the lineup, built for large and wide pneumatic setups.
It is not a separate system. The 86 mm XL uses the same L size ring as the 66 mm Wide Hub, so wherever the two overlap on tires, they overlap completely. What the extra width buys you is support across a wide tread: a 200×75 or a 220×89 sits on a hub center that reaches further under it, instead of overhanging a narrower base.
- Hub ring: L size (same ring as the 66 mm Wide Hub)
- Tire opening: 100 mm nominal, plus selected wider 94.5 mm tires
- Axle sizes: 8 mm, 10 mm, 12 mm
- Recommended axle and bearing: 12 mm axle with 6001; on a 10 mm axle, use 16100
- Best suited for: wide 8-inch and 9-inch treads, including 200×75 and 220×89
All three hubs at a glance
| Spec | 55 mm Standard | 66 mm Wide | 86 mm XL |
|---|---|---|---|
| Hub center width | 55 mm | 66 mm | 86 mm |
| Hub rings accepted | M size | M size + L size | L size |
| Tire opening | 94.5 mm | 94.5 mm or 100 mm | 100 mm + selected 94.5 mm |
| Axle sizes | 8 / 10 / 12 mm | 8 / 10 / 12 mm | 8 / 10 / 12 mm |
| Recommended bearing | 608 / 6900 / 6001 | 608 / 6900 / 6001 | 6001 (12 mm), 16100 (10 mm) |
| 6-inch tires | ✓Compatible | —Not compatible | —Not compatible |
| 7-inch / 8-inch tires | Selected narrow only | ✓Compatible | Selected wide only |
| 9-inch tires | —Not compatible | ✓Compatible | Wide 220×89 only |
✓ Compatible in at least one ring configuration | — Not a supported configuration
M Size vs L Size Hub Rings
On any NEXT hub, the ring is the part that decides whether a tire fits. The 66 mm Wide Hub is where this matters most, because it is the only hub that accepts both rings.
M size hub ring: 94.5 mm opening
The M size ring is designed for pneumatic tires with a nominal opening of 94.5 mm. Typical examples include:
- 160×70
- 165×72
- 190×50
- 200×50
- Certain 200×75 wide-tread configurations
The M size ring is the ring used by the NEXT 55 mm Standard Hub.
L size hub ring: 100 mm opening
The L size ring is designed for a nominal 100 mm opening, which covers most of the larger tire configurations. Examples include:
- 160×80 COBRA ST
- 200×75 MBS
- 9-inch pneumatic tires
- 9-inch wide pneumatic tires
Some wider 94.5 mm tires, including certain 200×75 configurations, can also run on the L size ring.
The L size ring is the ring used by the NEXT 86 mm XL Hub.
Do not pick a ring from the opening size alone. Tread width, tire construction, and sidewall shape all affect fitment. Confirm the exact tire model and its dimensions before ordering a ring.
Tire-to-Hub Compatibility Chart
The chart below covers Linnpower's main pneumatic tire options against each hub and ring combination. It is a starting reference, not an exhaustive list: tires outside this chart can still fit if their measured opening and tread width match.
| Tire model | 55 mm Standard | 66 mm + M ring | 66 mm + L ring | 86 mm XL |
|---|---|---|---|---|
| 6-inch tire 150×55 | ✓Compatible | —Not compatible | —Not compatible | —Not compatible |
| 7-inch street tire 160×50 | ✓Compatible | ✓Compatible | —Not compatible | —Not compatible |
| 8-inch AT tire 200×50 | ✓Compatible | ✓Compatible | —Not compatible | —Not compatible |
| NEXT Racing Slick 160×70 | —Not compatible | ✓Compatible | —Not compatible | —Not compatible |
| 190×70 MTB tire | —Not compatible | ✓Compatible | ✓Compatible | —Not compatible |
| 8-inch wide off-road 200×75 | —Not compatible | ✓*Compatible with verification | ✓*Compatible with verification | ✓Compatible |
| 9-inch tire 220×67 | —Not compatible | —Not compatible | ✓Compatible | —Not compatible |
| 9-inch wide 220×89 | —Not compatible | —Not compatible | ✓Compatible | ✓Compatible |
| COBRA street 160×80 | —Not compatible | —Not compatible | ✓Compatible | —Not compatible |
← Swipe the table sideways to see every hub option →
✓ Compatible | — Not a listed configuration | * Verify the actual tire opening and tread width before ordering
* For 200×75 tires, M or L ring compatibility depends on the specific tire's opening, tread width, and construction. Different 200×75 models are not identical, so do not assume a single 200×75 result applies to every 200×75 tire on the market.
A note on units: esk8 pneumatic tire specs are written in millimeters worldwide, so 200×50 means a roughly 200 mm outer diameter with a 50 mm tread width, which is the tire usually called an 8-inch tire. Riding in the US does not change the spec, only how you say it.
Which Hub Do You Actually Need?
NEXT 55 mm Standard vs NEXT 66 mm Wide
Both hubs are the same system at different widths, and width is the real difference. The 55 mm hub is built for smaller, narrower tires, especially 6-inch. It can also run selected 7-inch and 8-inch tires with a 94.5 mm opening, provided the tread is narrow enough.
One hard limitation: do not use the 55 mm Standard Hub with tires whose tread width exceeds 65 mm, even if the tire has a 94.5 mm opening. The narrow hub center will not let a wide tread spread properly, and installation can become extremely difficult or simply fail.
The 66 mm Wide Hub covers almost everything the 55 mm hub does, except 6-inch tires, and adds the larger and wider configurations through the L size ring.
Where the 86 mm XL fits in
The 86 mm XL uses the same L size ring as the 66 mm Wide Hub. Both hubs therefore fit the same 100 mm-opening tire family, and on tires they share, either one works.
What separates them is width. The 86 mm XL carries a hub center 20 mm wider than the 66 mm Wide Hub, so a wide tread — 200×75, 220×89 — is supported across more of its width instead of overhanging a narrower base. That is the reason this hub exists, and it is the reason we pair it with thicker axles.
Axles and bearings: 8 mm, 10 mm, or 12 mm?
All three NEXT hubs accept 8 mm, 10 mm, and 12 mm axles. On the 55 mm and 66 mm hubs, axle size only changes the bearing. On the 86 mm XL it also changes our recommendation: a 12 mm axle with a 6001 bearing is the intended pairing for a wide, heavy wheel assembly, and a 10 mm axle with a 16100 is the alternative. The hub itself does not refuse a smaller axle — the build simply has less margin as the wheel gets wider.
| Axle size | 55 mm Standard | 66 mm Wide | 86 mm XL |
|---|---|---|---|
| 12 mm | 6001 | 6001 | 6001 — recommended |
| 10 mm | 6900 / 16100 | 6900 / 16100 | 16100 |
| 8 mm | 608 | 608 | Supported* |
* An 8 mm axle on the 86 mm XL is an uncommon build. Confirm the bearing combination with support before ordering.
Choose the 55 mm Standard Hub if you run 6-inch tires, or narrow 7-inch and 8-inch tires you are not planning to change.
Choose the 66 mm Wide Hub if you want one hub that can move between tire sizes and openings, or if you are still deciding.
Choose the 86 mm XL Hub if your build is centered on wide 8-inch or 9-inch treads. Run it on a 12 mm axle with 6001 if you can; a 10 mm axle with 16100 also works.
Three questions, in order:
- What is my tire's measured hub opening? Near 94.5 mm means the M size ring, so the 55 mm or the 66 mm hub. Near 100 mm means the L size ring, so the 66 mm or the 86 mm XL.
- How wide is the tread, and how big is the tire? A 6-inch tire rules out both the 66 mm and the 86 mm XL. A tread over 65 mm rules out the 55 mm Standard. Wide 8-inch and 9-inch treads point to the 86 mm XL.
- What axle am I running? All three hubs take 8 mm, 10 mm, and 12 mm axles, so axle size does not eliminate a hub. It decides the bearing — and on the 86 mm XL it decides whether we recommend the pairing at all.
Tire-by-Tire Fitment Notes
6-inch tire
Built for the 55 mm Standard Hub only.
- NEXT 55 mm Standard Hub
The 66 mm Wide Hub is not recommended for 6-inch tires because its hub diameter is approximately 150 mm, which creates tire fitment limitations. This is the main reason the 55 mm Standard Hub was developed.
7-inch street tire
A street tire that runs on both the 55 mm Standard Hub and the 66 mm Wide Hub with an M size ring.
- NEXT 55 mm Standard Hub
- NEXT 66 mm Wide Hub + M size ring
8-inch all-terrain tire
An all-terrain tire that works with the following configurations.
- NEXT 55 mm Standard Hub
- NEXT 66 mm Wide Hub + M size ring
NEXT Racing Slick 160×70
A street-oriented racing tire designed for smooth surfaces.
- NEXT 66 mm Wide Hub + M size ring
190×70 MTB tire
A larger mountainboard-style pneumatic tire for off-road builds.
- NEXT 66 mm Wide Hub + M size ring
- NEXT 66 mm Wide Hub + L size ring
8-inch wide off-road 200×75
A wide off-road tire that supports several NEXT configurations, provided the ring and tire dimensions are confirmed first.
- NEXT 66 mm Wide Hub + M size ring
- NEXT 66 mm Wide Hub + L size ring
- NEXT 86 mm XL Hub
View 8-inch Wide Off-Road Tire →
9-inch tire 220×67
For larger pneumatic wheel setups.
- NEXT 66 mm Wide Hub + L size ring
9-inch wide 220×89
A wider 9-inch configuration for more contact patch and a wider off-road stance.
- NEXT 66 mm Wide Hub + L size ring
- NEXT 86 mm XL Hub
COBRA street tire 160×80
A street tire that requires the L size ring configuration.
- NEXT 66 mm Wide Hub + L size ring
View COBRA Street Tire 160×80 →
Hub Fit Is Not the Whole Story
A tire that mounts on a hub is not automatically right for your board. Once the tire is on, three things can still go wrong.
Tire sidewall clearance
Some pneumatic tires have wider or more rounded sidewalls. The tire can seat perfectly on the hub and still have its sidewall protrude far enough to contact the gearbox housing.
Motor mount clearance
Check clearance to the motor mount through a complete rotation of the wheel, not just at one position. Insufficient clearance shows up as rubbing, drag, and eventually damage.
Overall wheel dimensions
Tire diameter, tread width, sidewall shape, and wheel position all affect the final result. Compatibility also varies with your truck and drivetrain configuration, so two riders using the same tire on different boards can get different outcomes.
Before your first ride: rotate the wheel through a full turn and check clearance between the tire, the gearbox housing, and the motor mount. Confirm there is no rubbing or interference at any point in the rotation.
Frequently Asked Questions
Are the 55 mm, 66 mm, and 86 mm NEXT hubs different systems?
No. They are the same quick-release system in three hub center widths. The 55 mm hub takes the M size ring, the 66 mm hub takes the M or L size ring, and the 86 mm XL takes the L size ring. Nothing else about the system changes between them.
What is the difference between an M size and an L size hub ring?
The M size ring fits a nominal 94.5 mm tire opening. The L size ring fits a nominal 100 mm opening. The M ring is used by the 55 mm and 66 mm hubs; the L ring is used by the 66 mm and 86 mm XL hubs. Only the 66 mm Wide Hub accepts both, which is why it is the most flexible hub in the lineup.
Which hub fits a 94.5 mm tire opening?
The 55 mm Standard Hub, or the 66 mm Wide Hub with an M size ring. Use the 55 mm hub for 6-inch and narrow 7-inch or 8-inch tires. Use the 66 mm hub if you also want room to move to wider tires later.
Which hub fits a 100 mm tire opening?
The 66 mm Wide Hub with an L size ring, or the 86 mm XL Hub. Both use the same L size ring; the 86 mm XL simply has a wider hub center for wide treads.
What is the difference between the 86 mm XL Hub and the 66 mm Wide Hub with an L ring?
Width, and only width. They use the same L size ring, so both fit 100 mm-opening tires. The 86 mm XL has a hub center 20 mm wider, which supports a wide tread across more of its width — the difference shows up on 200×75 and 220×89, not on narrow tires.
Can I install 6-inch tires on the 66 mm Wide Hub?
No. The 66 mm hub has a hub diameter of roughly 150 mm, which makes 6-inch tires difficult or impossible to seat. That limitation is exactly why the 55 mm Standard Hub exists.
Will an 8-inch 200×75 tire fit the 66 mm Wide Hub?
Usually yes, but the ring depends on the individual tire. Some 200×75 models use a 94.5 mm opening and take the M size ring; others use a 100 mm opening and need the L size ring. Check the actual opening and tread width before ordering, because 200×75 tires differ between manufacturers.
What axle does the 86 mm XL Hub take?
The 86 mm XL accepts 8 mm, 10 mm, and 12 mm axles, the same as the 55 mm and 66 mm hubs. We recommend 12 mm with a 6001 bearing, because the hub is built for wide, heavy wheel assemblies. On a 10 mm axle, use a 16100 bearing. An 8 mm axle is an unusual pairing at this width, so confirm the bearing combination with support first.
What bearings do I need?
On the 55 mm and 66 mm hubs, use 608 for an 8 mm axle, 6900 or 16100 for a 10 mm axle, and 6001 for a 12 mm axle. The 86 mm XL uses 6001 on 12 mm and 16100 on 10 mm. Bearing choice follows axle diameter, not the tire.
How do I measure my tire's hub opening?
Measure the inside diameter of the bead seat, the inner lip that sits against the hub ring. Do not measure the outer tire diameter or the tread width. Near 94.5 mm means M size; near 100 mm means L size.
Why does my tire rub the gearbox or motor mount?
A tire can fit the hub correctly and still interfere with the board. Wide or rounded sidewalls contact the gearbox housing, and larger diameters reduce clearance to the motor mount. Rotate the wheel a full turn and check the tightest point before riding.
Can I run MBS or other brand tires on a Linnpower hub?
Brand name does not decide fitment. Match on measured hub opening, tread width, and sidewall shape. MBS 200×75 tires are commonly used, but individual 200×75 models still need their opening measured before you choose a ring.
Final Thoughts
The NEXT Quick-Release Hub system is built around one idea: let riders change tire size and tire opening without changing the whole wheel assembly. The three hubs are the same design at three widths, so the choice comes down to how wide a tire you want to run.
- NEXT 55 mm Standard Hub: the narrowest option. 6-inch tires, plus selected narrower 7-inch and 8-inch tires on the M size ring.
- NEXT 66 mm Wide Hub: the most versatile option, and the only hub that runs both the M and L rings across a wide range of tire configurations.
- NEXT 86 mm XL Hub: the widest option, on the same L size ring, built to support wide 8-inch and 9-inch treads and paired with 12 mm axles and 6001 bearings.
Choosing the right ring matters as much as choosing the right tire, and choosing the right width matters as much as either. Check the tire opening, tread width, axle, bearings, and physical clearance before you buy or install a new wheel setup.
Still not sure which hub or tire combination fits your board? Contact the LINNPOWER support team with your tire model, measured opening, and axle size, and we will confirm the configuration before you order.
Join the LINNPOWER Community
Running an unusual tire and hub combination? We want to hear about it.
Join the LINNPOWER Facebook Group to share your setup, ask fitment questions, and compare notes with other riders.
Subscribe to the LINNPOWER YouTube Channel for installation tutorials, maintenance guides, and product updates.

